Pin Vises

 

Swivel Head Pin Vise
79000
!

This swivel head pin vise has 4 steel collets making it perfect to hold 0 to 1/8 inch items. It will hold a #80 bit to a 1/8 inch shaft.

Double Ended Pin Vise
79001
!
This pin vise has 4 steel collets making it perfect to hold 0 to 1/8 inch shafts. It will hold from a #80 bit to an 1/8 inch

Long Double Ended Pin Vise
79002
!
This is a new long version of a double ended pin vise. It is recommended for jewelers, lapidary, hobbies and crafts, modeling, home repair, etc. This is a new double end pin vise that can be used as a hand drill with small twist drills. It has 2 double ended collets for holding wire, stock or tubing for filing. It holds burs, files, reamers and more. This pin vise has knurled heads 0 - 1/8 (2.8 mm) known as Swiss style. It measures approximately 9 inches long

Ball Head Pin Vise
79005
!
The ball top swivels on this 3 ¾ inch pin vise and has two steel collets so it can hold bits from 0 to 3/32. It has a nice smooth spin on the head to give you complete control for perfect small precise drilling.

Push Pin Vise
79050
!
This push pin vise has two steel collets making it perfect to hold 0 to 3/32 inch shafts. It is over 7 ¼ inchs in length

Mini Push Drill
79060
!
This mini push drill has a swivel top and sping loaded. It is perfect for holding very small drill bits like 70 to 80. It is 3 ¾ inchs in length.

Pin Vise and Drill Bit Set
79100
!
Made in USA

This 4 ¼ inch American Made Pin Vise comes with 12 American Made HSS drill bits #'s 52 thru 74, all even numbers. Drill bits store in the top.

12 Long Bits & Pin Vise
79102
!
Made in USA

These AMERICAN MADE  extra long drill bits are ideal for drilling deep.  Each drill bit is 2” long, American Made Tempered High Speed Steel  with #’s 52 – 74, every even number.  Comes with PIN Vise and indexed pouch for accuracy.

Keyless Finger Chuck
95420
!
This is a Keyless Finger Chuck that goes from 0 to 1/8 inch. It only fits the following Dremesl® #275, 285, 410, 595, 851, 950 and the new Ryobi.

Keyless Chuck
95430
!

This keyless chuck will fit any Dremel®, Ryobi, Wizard and all other moto tools. It has a standard 1/8 inch shaft and the chuck will open from 0 to 1/8 nch.
Never change a collet again

Finger Chuck with Collets
95450
!
This is a Finger Chuck with a 3/32 shaft. I will give you a free 3/32 collet just in case you don't have one. It goes from 0 to 3/32. For best results, I advise you to cut the shaft a little and always start at the lowest speed. I have sold hundreds of these with great results.

Mini Finger Chuck
95460
!
This is a Mini Finger Chuck with a 1/8 inch shaft. This is designed to hold those 70 to 80 drill bits in your Dremel® or moto tool. Only use with multi speed tools on slow.

Finger Chuck for Power Screwdrivers Regular
95465
!
This is a Finger Chuck that is perfect for your 1/4 inch power screw driver. It is great for holding bits from 0 to 1/8 inch.

Finger Chuck for Power Screwdrivers Large
95466
!
This is a Finger Chuck that is perfect for your 1/4 inch power screw driver. It is great for holding bits from 0 to 1/8 inch.

Pin Vise
79000
!

This swivel head pin vise has 4 steel collets making it perfect to hold 0 to 1/8 inch items. It will hold a #80 bit to a 1/8 inch shaft.